• 글쓰기
• 목록

How to Replace the replacement saab 9-3 key Key Battery For the Saab 9-3

Saab owners must follow a set of steps that are unique to add a second ignition key. This requires an electronic handheld computer, referred to as Tech-2 which is used by the dealer. Then a new key and transponder have to be purchased and then programmed to the car.

It is an excellent idea to rotate your keys so that one does not get damaged faster than the other. This will help keep your keys in pristine condition.

Replacement Case

As opposed to the traditional Saab keys of old keys, the new key fobs are equipped with electronics which makes it hard to make a copy. This has made theft of cars much more difficult than it was twenty years ago. It also makes it more costly to replace keys that were lost.

Saab 9-3 owners must have two keys that work. If one of them is lost, it costs a lot to get another one for the car because it involves replacing the CIM module and re-programming the locking cylinders. Dealers charge between $100 and $200 for this.

There are ways to avoid these high costs. Some parts dealers will use the code of a spare key to cut a brand new metal blade for a fraction of that of a dealer. The key, however, must be the same as the original to work correctly in your car.

You can also replace the case yourself by following these steps. You'll require an open-faced screwdriver and patience. With the screwdriver, slowly break the plastic and then separate the emergency key from the case. Once you have the case open, remove the electronics and put them back into your new case. Place the key with the correct badge inside the case.

Replacement Battery

The Saab 9-3 replacement battery is a cheap part that can be easily and quickly replaced. This YouTube tutorial for DIY user Cyclone Cyd explains how to replace the remote key fob battery in just four steps. This tutorial should work for any modern-day saab key fob however the procedure might differ slightly.

The button is normally located just below the saab key fob repair logo on the back of the fob. It is usually located next to the Saab logo on the back of the fob. Use a flathead to insert the screwdriver into the small hole in this button. This will be enough to allow you to open the case of the fob so that you can replace the battery.

After you have installed the CR1632 batteries, you can rebuild your remote key fob. You can then program it into your car. The entire process should take no more than a half hour at the most. It's a simple process that does not require any special equipment.

The process can be a bit more complicated in the event that you lose the key, but it's possible. The dealer has to find the VIN number of the car and then purchase a replacement key blade and a TWICE module with the correct unique code. The dealer will then have to program the key using MDI, a new software tool.

Replacement Key Fob

The key fob has an internal battery that is used to lock and unlock your car. Batteries are able to last for a short time and will eventually fail. This is a problem that occurs with all vehicles and the good news is that you can replace the batteries in most key fobs without having to replace the entire case. You can purchase replacement fobs on Amazon that have all the electronics already installed, so you can just pop open the case and replace those batteries that are old. It is important to remember that you will need to take out the emergency key first. you can do this by inserting the small screwdriver flathead into the slot located in the middle of the case. The case will split once you move the screwdriver around it.

If you are about to replace the keys, ensure that you have a spare, because this can cut down the total cost by a significant amount. If you have a spare, you can ask the dealer cut an entirely new key and then program it to your car, which is much cheaper than replacing the whole key fob.

It is possible to add a second key to your car If you don't already have one, however it requires an extensive amount of research and effort. The cost of adding a second key is several hundred dollars and it also requires the programming of the car's computer. Professionals can do this however, it's a costly option.

Replacement Ignition

As opposed to earlier saab 9 3 key replacement automobiles, the new SAAB 9-3 models feature an advanced alarm system that is based on a coded key. This means that should you lose only one working key, acquiring another one can be very expensive since the car has to have a computer module installed, and it must also be programmed to accept an additional key. Even a dealer can charge hundreds of dollars to program the new key if they are unable to do it.

If you've lost your sole working key, a dealer will repair the computer in your car (known as the CIM or SAAB TWICE) in order to make the replacement, and will charge you a premium price for it. Instead we can reprogram the EEPROM in your current car computer to allow it to be programmed for an additional key, and save you over 50% of the price you be charged at a dealership.

If you've been an owner of a 03-11 SAAB 9-3, you likely have noticed that the ignition switch isn't all that durable. If the ignition key you have isn't working properly, you should consider replacing it. They can become sticky and the buttons have been known to fall off. It's not so difficult as it may seem to replace the ignition key. With the appropriate tools, it could be accomplished in a matter of minutes.